Martindale pilling instrument

info@qinsun-lab.com Get Quote

The Martindale pilling tester is suitable for testing the pilling degree of fabrics such as IOS4802.2, ASTM D4970, ISO12945-2, etc. Principle: A circular specimen is rubbed against a fabric of the same material under a given pressure using the Lissajous graphical motion trajectory. After reaching the specified number of revolutions, the pilling and pilling level of the specimen is evaluated. It is also applicable to the wear resistance test of fabrics such as IOS13775, ASTM D4966, ISO12947, etc. The principle is that under a certain pressure, the circular fabric sample rubs against the standard abrasive according to the Lissajous curves motion trajectory, causing the sample to be damaged. The wear resistance of the fabric is represented by the number of times the sample is damaged.

Main features:

The Martindale pilling and pilling instrument is designed based on the advantages of similar instruments both domestically and internationally. It has a beautiful and elegant appearance, adopts a touch type display screen, has an easy to understand interface, and is easy to operate. The microcomputer system adopts two counting methods, which are intuitive and easy to set. Eight workstations are tested simultaneously, improving the efficiency of the test. The instrument also has two types of Lissajous 24mm x 24mm, 60.5mm x 60.5mm motion trajectories and various supporting accessories, which can adapt to various test method standards.

Applicable scope:

The Martindale fuzzing and pilling tester can test the wear resistance and pilling performance of various plants. Under a certain pressure, the sample is subjected to continuous directional friction with the designated abrasive, and the degree of wear and pilling is evaluated by comparing it with standard parameters. Touch screen control, equipped with a comprehensive programmer, capable of pre programming batches and total counts, and setting the count for each test head separately; Four speeds, including standard speed, can be selected.

Compliant with standards:

ASTM D4970 ISO 12945.2, IOS 4802.2/13775/21196.1/21196.2 ASTM D4966 ISO 12947 FZ/T 20020 BS 3424-24/5690 ISO 12947.1/12947.2 Mamp;S P17/P19/P19C NEXT 18/18a/18b ISO 5470-2 IWTO-40 JIS L1096 8.17.5 Method E Woolmark TM 112/196 BS EN 388/530/13770 ISO 20344

Technical parameters:

1. Number of workstations: 9 workstations;

2. Counting range: 0-999999 times

3. * * Travel: Horizontal 60.5 plusmn; 0.5mm, vertical 24 plusmn; 0.5mm

4. Mass of pressurized material:

a. Gripper: 200 plusmn; 1g

b. Weight of fabric sample: 395 plusmn; 2g

c. Furniture and decoration sample hammer: 594 plusmn; 2g

d. Stainless steel disc: 260 plusmn; 1g

5. Effective friction diameter of grinding block:

A-type 200g (1.96N) friction head (9kPa) yen; 28.8-0.084mm

B-type 155g (1.52N) friction head (12kPa) yen; 90-0.10mm

6. Relative movement speed between gripper and grinding table: 20-70r/min (adjustable)

7. Sample pressing hammer mass: 2385 plusmn; 10g

Instrument configuration and consumables:

1. 9 sets of sample clips;

9 weights of 2.9kPa and 12kPa each;

three Phi; 38mm Phi; One set of 140mm samplers each;

four Phi; 38mm Phi; One 140mm sampler pad each;

5. A set of pilling test kits;

Take a set of 50 standard samples;

A set of standard pilling samples and a piece of SM-25 standard grinding cloth 1.6m x 5m;

8. One set of standard foam 1.5m times; 0.5m (4 pieces/set);

9. A standard felt piece;

ten Phi; 20 90mm felt discs;

eleven Phi; 38mm Phi; 50 blades for each 140mm sampler.